What to Expect with the ECMPS Tool Transition (ECMPS 2.0)
CAMD is in the process of replacing the outdated ECMPS Client tool – now over a decade old – with a new, web-based program: ECMPS 2.0. Learn key deadlines and important information about upcoming changes.
Quick CEMS Audit Prep Checklist
Use our quick checklist to pass an EPA CEMS audit of your facility. Use a proven CEMS DAS like StackVision and Prism for critical data and have current information about your designated representative, record keeping, QA/QC plan, permit & acid rain program at hand.
How to Improve Your Quality Assurance Filing Process
Don’t wait – prepare before the end of the quarter! Learn how to improve your quality assurance (QA) filing process, including our 7 Steps for success.
What is the EPA 40 CFR Part 75 Regulation?
Learn about the Part 75 rule created by the U.S Environmental Protection Agency (EPA) to establish requirements for monitoring and recordkeeping of air pollutants emitted from electric generating units (EGU) in support of the Acid Rain Program (ARP).
How StackVision™ Prevents Reporting Discrepancies
Learn how StackVision’s Database Locking Wizard can help you prevent emissions data discrepancies during reporting.
What is the Protocol Gas Verification Program (PGVP)?
Learn about the Protocol Gas Verification Program (PGVP) and how it applies to your site.
Recommended Monitoring Plan Checklists
When you have and use in-house procedures, checklists, QA/QC plans, and other organizational aids, you can achieve greater consistency and perform your tasks more efficiently. They also serve as an important reminder to perform infrequent but repetitive tasks and activities. Use our guidelines and helpful checklists to make sure you are prepared.
What are the MATS Revisions from September 2020?
Learn about the final revisions to the Mercury and Air Toxins Standards (MATS) and where to find resources on these revisions.
How StackVision™ Helps Refineries With RSR Regulations
Learn how using a data acquisition system such as StackVision helps refineries meet extensive Refinery Sector Rule (RSR) regulations.
What is the EPA 40 CFR Part 60 Regulation?
40 CFR Part 60 regulations, otherwise known as New Source Performance Standards (NSPS), are pollution control standards issued by the U.S. Environmental Protection Agency. Adherence to these performance standards maintains the air quality in an area or region by reducing or eliminating pollutants’ release.
Bridging the RSR Compliance Gap: Part 2
This article appeared in Hydrocarbon Engineering’s August 2020 issue. This article focuses on US EPA approved alternative 131 (ALT 131). ALT 131 allows for total calibration cylinder net heating value (NHV) as an alternative to the PS-9 requirement that specifies calibration and calibration check individual component agreement.
NOx Correlation Testing Checklist
Facilities have in-house procedures for NOx Correlation Testing, as required by the Environmental Protection Agency. As with all procedures, preparation for NOx Correlation Testing is extremely important. Use this pre-testing checklist for assistance.
Bridging the RSR Compliance Gap: Part 1
In this article, which appeared in Hydrocarbon Engineering’s July 2020 issue, you’ll learn how, with the introduction of RSR and the copious amounts of data now required for compliance, many refineries are turning to a data acquisition system like Stackvision to meet regulatory requirements.
How to Perform Fuel Flow to Load or Gross Heat Rate Checks
Learn how to perform a quarterly stack flow-to-load (F/L) or gross heat rate (GHR) check on your fuel flow monitor.
Fuel Flow Meter Accuracy Checklist
Helpful advice on Fuel Flow Meter Accuracy Checks procedures to comply with Part 75 Appendix D requirements.
Breaking Down Part 75 Appendix A Span and Range Equipment Specifications
Learn about Part 75 Appendix A Span and Range Equipment Specifications with this general overview and review.
How to Perform Quarterly Linearity Checks
Learn tips on how to perform a linearity check as part of the required quarterly QA/QC on your CEMS Analyzer.
What is the EPA 40 CFR Part 63 Regulation?
The Part 63 emissions standards (NESHAP) are for hazardous air pollutants not covered by National Ambient Air Quality Standards (NAAQS) and emitted from natural and human-made sources, including volcanoes, wildfires, motor vehicles, industrial facilities, and oil refineries.
The Ultimate Guide to Automating Daily Validations
Learn How to Automate Daily Validations in your facility’s Continuous Emissions Monitoring Systems (CEMS)
Conducting Primary Element Inspection Reports
Helpful advice on conducting primary element inspection reports at least once every 20 calendar quarters using a baroscope.